Clamping Pressure, Wood Hoarding, Iron and White Oak

This Episodes Questions:

Brians Questions

I have a question for you about glueing up table aprons. And I’m mostly referring to large dining tables. The aprons I’m making are generally w 8/4 stock roughly 4” width. I can manage to get the legs and the aprons milled and cut square. All my joinery is w dominoes. Whenever I do the glue up everything is slightly out out square despite everything being square prior to glue up . I have pipe clamps and parallel clamps and have tried both. For some reason I can’t get the clamping pressure or positioning right. Any tips would be appreciated. Bryan

Hello everyone,
Wanted your advice on dados and what I may be doing wrong. When I cut the dado and mating piece I make sure to get a good tight fit during the dry fit. My issue comes up when I’m sanding. I’ll take all the pieces apart and sand them to the desired sand grit (180 or 220 depending on finish). But when I go to glue up my mating piece is now loose in the dado. Should I be making the dado smaller, should I just wait to sand till it’s all glued up or do you have any other advice?

Thanks,
Paul at Twin Lakes Workshop

Guys Questions

I have listened to all your podcasts and have very much enjoyed and learned from them. I listen to primarily three woodworking podcasts and Woodshop Life is far and away the best.

I have to confess I am a wood hoarder. I do a lot of small projects (scroll saw, boxes, and the like) and end up with small pieces left over that should be good for something. But how do I organize them and what size is too small, in your opinion, to be useful? The same applies to pieces left over after building furniture or other large projects? Do I just throw everything in the burn pile or is there a logical way to sort and store small pieces of lumber?

And one small criticism: need to update the website with Brian’s information since he is officially part of the podcast. Roger Martin

Hey there fellas! I’m with a small furniture and cabinet shop called Silt Studio in Atlanta. Love the podcast and the great wealth of knowledge you guys bring to the world of woodworking. Guy, don’t let anybody tell you you’re wrong, they’re never right. I have a question about the relevance of our table saw. It’s a Powermatic PM2000 (I know guy loves his)with a 5×5 outfeed and a 36” rail extension. It’s really been a great workhorse for our shop. The space is about 3000 sq ft and we are quickly outgrowing the footprint for the amount of kitchen and cabinet jobs we’re taking on. There are also columns on a 9’x 14’ grid pattern so the space isn’t wide open. We’re talking about getting a large slider to facilitate speedier and more accurate square cuts. Currently we’re ripping down sheetgoods with our festool track saw then finishing on the table saw. If we get a slider, a large chunk of our milling/cutting space would be taken up. Is it worth keeping the powermatic and just losing the outfeed to save space or can we do everything we need to on the slider? We’re considering the laguna 12/8 model slider. Looking forward to your thoughts! Thanks so much, Sam

Huy’s Questions:

Hello gentlemen.
Great woodworking podcast. I am in the market for a drum sander. Currently I have a Jet 22-44. It is a love/hate relationship with all the known issues. The budget would be around 2,000-3,000. I was thinking arbor open ended powermatic 22-44 o it would be better to get Grizzly 24 or 24, or something similar that is closed ended. Also would you recommend single or double. What about finding bigger 37” or a similar from shops liquidations. I know there is wiring and things like that. I have a hobby workshop with some 220 equipment. Like I mentioned it is a hobby now maybe it will grow may it will not. I originally got the openeded sander hoping that I can send wider boards (stupidly table tops) but obviously it is not as easy as it would seems to be. I do not know if that helped on made my question more murky. Sometimes there a good deals on Facebook Marketplace place but those deals do not last long and you need to be ready. There was Grizzly G1066R for $1,300 and now I regret not buying it. Any suggestions would be welcome. Thank you. Derek

Question for the podcast: When using white oak for trim, what fasteners can I use that won’t cause the tannins in the white oak to react to the metal of the fasteners? Thanks guys. Jay

Brians Back!, Taping Veneer Seams, Making Interior Doors, and MORE!!

This Episodes Questions:

Brian’s Questions:

Ashtin here Hey guys love the podcast thank you for putting out good content for all of us to hear

My question is I’m very new to the woodworking community I don’t have a shop or a space I work in I use all mobile equipment I do all my work outside I want to know what projects I can do that will help build my skills in and my confidence
I have a DEWALT Dw7491rs Table saw
A Bosch router table Ra1181
A craftsman jointer Cmew020
A wen 6524 spindle and belt sander combo
A dewalt Dws 780 miter saw
I do have a Incra 1000se
Also what blade would you recommend for my table saw for an all around use? I have been using Diablo blades sense I have had it. Ashtin

Brian also gives a nice PSA on shop safety and how thiungs can go wrong quickly

Guy’s Questions:

I’ve been doing some veneering using a vaccum bag. Mostly just panels for doors and box lids. When I join two pieces of veneer together at a seam I’ll use blue painters tape to hold the seem together. My.problem is when I get it out and start taking the tape off I’ll get some of the veneer fibers coming off with the tape. How can I prevent it from happening? Thanks
John

Hi guys. Love the podcast. I’ve learned a bunch from you all. My question is about end grain. I’m building a cherry night stand that has a shelf that will be 20″ long and about 17″ wide. I’m making the shelf from solid cherry as well. The 17″ dimension end grain will show on the left and right sides of the night stand. I made my own cherry veneer from the stock I have (it’s about 1/32″ thick) and was thinking I could edge band it to the ends. But if I do that, the glue holding the veneer will prevent the wood from moving, right? I was even thinking about using the banding so that the grain follows the top (like a waterfall). But it doesn’t solve the glue issue. Am I correct in this thinking? How can I dress up the ends so that it doesn’t look like amateurish? Or should I just sand the end grain to a very fine grit and/or seal the end grain before finishing so that it doesn’t get darker than the shelf itself?
Thanks so much.
Anthony

Huy’s Questions:

Hello Gentlemen,

I’m planning on replacing the cheap hollow-core door that leads from my conditioned basement to my workshop garage.

Any advise on materials? I know MDP is flat but edges are brittle. Can I use an mdf or plywood core and dress it up with thinner material? How should I go about this while accounting for wood movement? My jointer is the limiting factor, bench-top with only a couple feet in totable bed lengths combined.

Thanks Again, Dave

I’m an “aspiring” woodworker in Harvest Alabama. I have a 1 car garage with a 5x8x6 tornado bunker in the middle of the floor. If you had that, is there any way that you would reuse that space to your advantage? Not just storage space, but actively- like dust collection, or an extra long panel saw.
Tom

How Thick of Plywood?, Proper Hand Saws, Face Masks and MORE!

This Episodes Listener Questions:

Guys Questions:

Hello Guy, Huy, and Brian,
Loving the content you guys are dishing out. Keep up the good work!

I have my sights set on a jointer in the near future as I would like to save time and energy squaring lumber. My preference up until now has generally been to buy new tools and the thought of refurbishing/repairing anything used has not appealed to me. However, the cost difference between a new/used jointer has me thinking differently. Also, the jointer seems to be one of, if not the easiest, of the big woodworking machines to refurbish given its simplicity. Correct me if I am wrong in this thinking. Curious to hear your thoughts if you think it is worth my time and effort to buy a used jointer or should I go new? What should I look for if I were to go used? I realize that moving a big machine like an 8″ jointer will be challenging, but I can easily get some friends together and rent a trailer to get the job done if the cost savings are great enough. Plus some beers and pizza for the helpers will help. Thanks! -John

Hey Folks,
Thank you for for the podcast. I love how quickly you jump right into the questions! Here’s mine: I’m building a set of screen doors for a cottage. The doors will be exposed directly to the weather in Quebec.
The doors will get a lot of abuse. They will close with a spring and slam frequently. The screen will run the full length of the door. I’m hoping to use a domino for the joinery.
3 questions: 1) what glue should I use? 2) what wood should I use? 3) How should I finish the doors?
Thanks ! Larry

Gentlemen,
First let me thank you for the podcast. I recently stumbled upon it and you three are now my regular company on my daily commute. Thank you! I consider myself a beginner hobbyist woodworker. My shop is the third bay of a 3 bay garage. My question is about when it is appropriate to use 3/4 inch vs 1/2 inch plywood. 3/4 inch plywood is so common, I wonder if it is needed as often as it is used? What kinds of applications need 3/4 inch plywood and what are some examples of when 1/2 inch plywood would be sufficient? I know that I am often guilty of over building projects and I suspect many woodworkers are. 🙂 Thanks for any information you can provide.
James Aydelotte

Huy’s Questions:

One more quick question, I’m working on getting into proper jointery. Is a nice hand saw worth investing in or is there an affordable option I can go with. I do mostly custom trim work but getting into more furniture grade work so it’s not something I will be using all day every day. Arntz Construction

Huy,

I am considering a clearvue and Oneida cyclone dust collector. I know you have the clearvue. What is your opinion of its performance? I have heard that it is very loud, what do you think? Thanks! Don

I’ve been doing more and more hand tool woodworking, so less and less dust-producing activities, but I still have occasion to use regular power tools for certain things. I’ve been striving to get better performance from my roll-around single stage D/C (with add-on cyclone pre-separator) and upgrading my hand-held power tools to ones with better built-in dust extraction… but there are still operations (edge cuts on the TS or with the router) that just spew crap everywhere. One area I need to probably do better on is wearing some sort of dust mask and/or respirator. I’ve avoided wearing them in the past, due to having a beard and knowing that masks get a very poor if any seal as a result. I’m considering getting something like a Trend AirShield (powered respirator / face shield), and was wondering if you have any other suggestions? Monte

3D Printed Jigs, Spraying at Home, Jointing an Edge and MORE!!

This Episodes Question:

Guy’s Questions:

Why hello gentlemen. I have a crazy question for you all. I am about to build a vanity for my bathroom out of poplar. I am leaning towards staining the vanity, but I don’t know what to put on the vanity to protect it from moisture. Do you guys have any suggestions? If so, it would be very helpful.
P.S. I am always looking forward to listening to show keep up the amazing advice
Thanks, Ethan Thompson !

Hi guys!
Alissa’s question from the your last episode spurred a question if my own. Alissa asked about homemade box joint jigs and the consensus seemed to be that making your own box joint jig is more trouble than it’s worth because of the precision required (down to a few thousandths if an inch) and because of wood movement.
I was wondering if you had any thoughts on using 3d printers for jig construction. My only experience with 3d printing was about 15 years ago when we got to use a primitive 3d printer in middle school woodshop class, so I don’t really know the capabilities of 3d printers today.
Do you guys think it would be beneficial or even possible to 3d print components to homemade jigs (anything from a miter bar to a complete jig)? It seems like 3d printing would give you more precision and no movement, unlike wood.
If it is possible, What jigs do you think would lend themselves best to bring 3d printed? Andrew

After hearing Guy mention Target coatings and Emtech finishes I signed up for their email. They had a nice year-end sale and I ended up ordering their Emtech spray kit which is the Fuji LX-20 and some accessories. I’m new to spray finishing. I’m lucky enough to have a large 80 gallon 5 HP compressor, so I have plenty of air.
I’d like to know Guy’s procedure for spraying small shellac projects. I’ve heard him mention he just whips out his spray gun and it’s a quick process. Do you lay down drop cloths? Do you do anything for ventilation – I know with solvent and oil finishes you’re supposed to, but I’m wondering if you bother if it’s a small piece. Do you have a fan setup to blow overspray away? I will, of course, wear an organic filter respirator for any spray finishing I do, whether water based or not. I haven’t purchased a respirator yet, any recommendations? Scott Goldthwaite

Huy’s Questions:

Hey guys, I’ve finally got caught up on all the podcasts and look forward to hearing the next one. I have a multiple part question here. I just got a commission on a 12 foot walnut bar and matching 8-10 foot table. My next purchase is going to be a jointer and I was wondering if a 74 or 76 inch bed jointer will be long enough or if I should just cut with my tracksaw and build a shooting board and joint everything with a hand plane? Also what would you use to dye and finish? Do you use pore filler to get a glass smooth surface or just let the finish take care of everything? Arntz Construction

Hello guys, I found your podcast a couple months ago and I’m hooked and really enjoy all the knowledge you share. I appreciate you guys taking your time to produce the podcast. My question is for my Rikon Benchtop Radial Drill Press (Model 30-140). I purchased this drill press a couple of years ago but have rarely used it mostly because of time constraints. But when I do use it, I have an issue with chuck runout. I’ve spent more time working on it then using it at this point. I checked the chuck spindle runout, and it is about .001 and once the chuck is installed, the chuck has .003 to .005 runout, with a new Fisch drill bit installed the runout on the drill bit shank varies .005 to .007 runout. Given the runout I have, I can’t get a decent hole when drilling anything. I’ve followed the instructions closely and cleaned all grease from the spindle and chuck and have reinstalled several times. I’ve tried several techniques of tightening the bit in the chuck which changed nothing. Is this a problem that is common, and do you have a recommendation to fix it, or can you recommend a better chuck? I’m considering purchasing a Grizzley Keyless chuck. Or should I sell this drill press and purchase a different one that would meet the needs of woodworking better? Thank you for your advice and keep up the great job on the podcast. Daniel Held, Fort Colllins, CO

Hey fellas. A buddy of mine asked me to replace some bad fence slats on his driveway gate. The boards are 1/2″ thick tongue and groove and look a lot like pine to me. I have a couple questions. First, do you think it’s safe to use pine to get the best match with the existing boards, or should I just go with redwood and hope that it blends in when the entire fence is restained? This gate is in Los Angeles, so we don’t get much moisture. My second question is regarding the design of the tongue and groove. They have a sharp “v” profile and don’t look like anything I’ve ever seen in the big box stores. (Photo attached). Have you guys seen this type of profile on a board before? Where would you recommend I try to source these replacement boards from? And do you have any recommendations for how I might go about milling up my own stock if I cannot find a match here in town. Thanks for all your advice. Matt Miller

Design Workflow, Bad Tools, Outdoor Projects and MORE!!

Guy’s Questions:

Guys,
Recently I’ve been trying to expand my meager wood shop with budget friends older tools. (Most recently a delta x5 6” jointer to fix up and repaint for example).
What would you look for when shopping for a used band saw you’re hoping to re-saw with? Where do you look for parts for older/discontinued tools? Any advice on tools that are best to just buy new?
Many thanks, Dave

Can you share about your design process? My biggest challenge is coming up with designs or finding plans (or redesigning plans) that are going to come out terrific without being too far above my skills, the tools I have, or my available time. Do you ever make prototypes or miniatures first? Do you do your planning in Illustrator, Sketchup, Rhino or ? Or do you just make notes and sketches on paper? And where do you keep your notes so you can recreate the same results?
For context: I discovered woodworking during the pandemic and fell in love with it. I’m a senior woman and it’s a wonderful hobby for me (not a career or a side hustle). I’ll never make lots of the same item for selling, but making only one doesn’t work because I don’t get good at it until I make at least 3. Trish

Thank you so much for covering my question about building a Butcher Block. I was shocked that Guy could speak French!!! I should not be surprised as Guy is a French name (pronounced Gkee). However, I am not familiar with the expression he used, but he is excused since he prefaced it with “Pardon my French”. Guy, you are forgiven, but if you want to use some really good French salty words to punctuate a thought, I am here for you buddy. We frogs need to stick together. On a side note, I have another question. I would eventually like to purchase a drill press. I really like the Nova Voyager and its direct programmable drive. My question is, what is the advantage of a free standing vs a bench mount drill press. I can see the advantage of a bench mount as it can provide storage space below. But why would any wood worker prefer a free standing unit? I believe I saw in huy’s video he does have the Nova drill press. From Thailand, Bert Plourde

Huy’s Questions:

Hi guys! Thank you for the great podcast. I look forward to listening to half of your show on the coincidentally timed drive to our local Woodcraft, and the other half on the way home. You put out great information, and humbly have the best show out there.
I have a question about sanding mops, and don’t know if any of you have experience with them. I’m currently making a large batch of ‘Contemporary Door & Drawer Pulls’ based on Larissa Huff & Robert Spieces’s article in FWW issue #289. Using Walnut.
One of the last steps in the article says, “To further refine the shape, and give the pull a nice soft quality, we finish up those hard to reach edges with a flap sander in the drill press. This sanding tool gives the pull a wonderfully tactile feel…”
After looking at the sanding mops in the Klingspor catalog, I’m a bit overwhelmed by the many options.
I’m curious as to which grit (grits) you might suggest to get that oh so important ‘wonderfully tactile feel’. I also wondered if there is a particular manufacturer you’ve had success with.
Thank you for your help!
Kevin Long

Hey guys,
As a hobbyist I like projects where I have to figure out something new (but not too extreme).
Sometimes I will modify a plan to make it more functional, more interesting, or just so I don’t get bored. Most of the time I don’t regret it, but occasionally I do kick myself.
As professional woodworkers how do you balance the need to be efficient and the desire to be creative?
Thanks, Chuck

Hello gentlemen,
I am in the middle of a remodel that will finish with painting the outside. I am going to make shutters for the windows and would like suggestions on what wood to buy. They will be painted.
I live in California and won’t have woods like alder or ash or southern pine available. The most common outdoor wood around here is redwood but that is normally stained and not painted. Can you use softwood in that application? Would even pine work?
I would love your thoughts.
Thanks, Rick